Image source: http://www.q17.org/crafts/stainedglass3.jpg
To apply placing earrings to the zinc body, lightly flux the ring and the area of the body where the ring will be attached. The area in that you just attach the earrings should be where the zinc body meets a solder seam. Next, solder the earrings to the zinc body. Be sure the ring extends over the edge of the body. If you are going to add a wood body to the stained glass piece don't attach earrings to the zinc body.
When mounting body on your art work, be sure that all edges of the glass are secured into the full depth of the zinc body. Otherwise, you will time out dissatisfaction after you solder the pieces together. As recounted, T-pins are advised to be sure and hold the body tightly anchored to edge of the glass and deep into the channel of the zinc body.
A zinc body on stained glass panels is a need to-have for constitution and rigidity. The zinc body is additional once the design is cut, foiled and soldered. The process of adding a zinc body is accomplished by following seven steps.
I hugely propose the riding placing earrings that have been twisted together as these are such a lot stronger and normally tend not to pull apart after the art work has been placing for it slow. I have experienced single wire hooks in point of announcement failing and a piece or two has dropped and broken. Save yourself grief (take it from me) and only use the twisted, as a result stronger placing earrings.
Some areas of outrage:
After zinc body is connected, be sure to exploit flux remover and do away with all flux residue.
If riding a wood body, a increased look is always produced by mitering the corners of the wood. Simple 45 degree cuts on the end of all body members easily accomplish this. When mechanically attaching these pieces of body, I strongly propose the use of a just suitable carpenters glue and one screw for long term placing safety. Additionally, wood frames come in all sizes, inclusive of width, thickness and specie of wood. Decide how you need to finish them, paint or stain. This will permit you to exploit the suitable wood for the suitable job and not detect yourself painting oak wood. Oak is too expensive and lovely to disguise under paint personally. Mechanical placing fasteners that include screws into the wood should be used.
1. First, measure the length of zinc came needed for each side.
2. Then, decide inside of the event you prefer straight cuts or mitered cuts for the corners.
3. Using a came saw or a fine tooth hack saw, cut the zinc came to the length and mind-set you need. Initially, you may be able to even need to chop the pieces long then re-cut when you dry fit the came to the stained glass piece.
four. Once you have all of the zinc came cut and fitted to your piece, insert the glass into the came channels and hold zinc in place riding t-pins. If you are riding Handy Hangers, you would insert them into the came corners suitable through this step.
5. Now flux the corners of the came body and all of the solder seams that touch the body
6. Then, solder each joint of the body and the adjacent solder seams.
7. Once, the first side is done, sparsely flip the piece over and repeat the process on that side.
Hanging earrings can be purchased or easily made by riding copper or silver wire. To make your own placing earrings, wrap wire around a pencil or other item to get the diameter you need. Then just cut it, making a small circle. If you need stronger earrings, cut two or three lengths of wire and twist them together. The twisting can be done easily by placing one end of the strands in a vice and the opposite end into the chuck of a drill. Rotate slowly until eventually the desired volume of twisting is completed. Then wrap the twisted wire around a pencil or other item and cut.
Mitered cuts look better personally, especially inside of the event you are not riding a wood body. Actually miter cuts are not that such a lot harder to complete, so why not be professional inside of the first place? Small electrical body cutters, 2 blade, are to be had for around $20. This is worth it personally.
When soldering the corners or the seam lines connecting the body, you will see a slight upward thrust to the solder. It is common to look the specified solder at these problems, but after patina is applied, these blend together and look fine. Be careful as to not build up too such a lot solder at these locations or this may be hugely seen when finished.
Please note that zinc frames are to be had in a form of sizes, widths. Each one, however, laps over the edge of the glass the comparable volume. So, the only cause for going to a bigger width is looks. Additional strength may be gathered in case your stained glass piece is enormously super. Any piece over 30 wide or tall should definitely be framed inside of the largest dimension zinc body to be had.
